Product Review/MRB Engineer - Levels 3, 4 & 5 - 100% ONSITE
REQ #66467 LEVEL 3
PAY $66.00
OPENINGS/SLOTS: 2/3
Basic Qualifications (Required Skills/Experience):
• Bachelor's or Masters of Science Degree from an ABET OR ABET equivalent accredited course of study in Engineering
• 5 or more years of experience in structures, systems, design, or production engineering (Mid- Level).
• 2+ or more years of experience in prior Engineering Materiel Review Board
REQ #66466 Level 4 THIS ONE HAS MORE SUB SLOTS THAN THE OTHERS!
PAY $83.00
OPENINGS/SLOTS: 2/8
MUST HAVES:
Basic Qualifications (Required Skills/Experience):
• Bachelor's or Masters of Science Degree from an ABET OR ABET equivalent accredited course of study in Engineering
• 10 or more years of experience in structures, systems, design, or production engineering (Senior- Level).
• 5 or more years of experience in prior Engineering Materiel Review Board
REQ #66468 LEVEL 5
PAY $105.00
OPENINGS/SLOTS: 1/4
Basic Qualifications (Required Skills/Experience
• Bachelor's or Masters of Science Degree from an ABET OR ABET equivalent accredited course of study in Engineering
• 14 or more years of experience in structures, systems, design, or production engineering (Expert - Level).
• 7 or more years of experience in prior Engineering Materiel Review Board
Preferred Qualifications (Desired Skills/Experience):
Liaison engineers that have experience across the following, will be looked for:
• Understanding for materials
o Material types - steel, aluminum, titanium - strength/capabilities
o Material forms – bar stock, forgings, castings and reactions to machining
o Post machining processing
• Understanding machining and machining limitations
o Geometry and sequencing for material removal (multiple pass, speed and feed of cutter)
Machine practices – machining, broaching, honing, etc
o Load path analysis for complex, integrated shapes – thin walls, undercuts, mismatches
o Surface condition and prep – discoloration, burns, drill/cutter breaks (FOD)
• Understanding of machined part dimensions and tolerance (GD&T)
o GD&T – True position, parallel surface, bonus tolerance, etc - used heavily (GD&T training 77100 Course – minimum)
o Interpret drawing datums, surfaces, profiles for tolerancing
Examples - requirements between gear/shaft fit up into housings, fit up of housing sections (base and cover)
o Spatial Analyzer analysis/modeling of discrepant conditions
o Metrology - methods, limitations, and interpretation
• Understanding of gears/shafts and gear interaction
o Gear table understanding
o Details - Teeth/spline profiles, runout, measurement over wires
o Install – gear patterns, gear engagement, bearing/shaft fit
• Understanding of material processing
o Heat treat, induction hardening, stress relief
o Shot and glass peening, abrasive blast cleaning, etching
o Plating – cad, chrome, Zi-Ni
o Finishing – anodize, passivate, primer and paint sequence
• Understanding functional test requirements
o Diagnosing impacts to operation and performance at the airplane level
o Range of FT acceptance – RPM, Torque, gaps/clearance
• Understanding of general repair for machined parts
o -M bushings, heli-coils, and inserts on oversized bores and holes
o Blending on machined materials, re-processing, re-finishing requirements
o Corrosion protection post processing rework - seal and primer requirements
Typical Education & Experience: Education/experience typically acquired through advanced technical education from an accredited course of study in engineering, computer science, mathematics, physics or chemistry (e.g. Bachelor) and typically 9 or more years' related work experience or an equivalent combination of technical education and experience (e.g. PhD+4 years' related work experience, Master+7 years' related work experience). In the USA, ABET accreditation is the preferred, although not required, accreditation standard.
The Structures Company LLC is an Affirmative Action/ Equal Opportunity Employer (or AA/ EOE)
Job Location: Portland, ORE
Rate: $66-$105/Hr. DOE
Per Diem: Yes
Overtime: Possible
Duration: 12 Months
Start Date: ASAP
Input Date: 08/07/2025
Attention: Debbie Aubert
Address: P O BOX 2278
City, State: SEAL BEACH, CA 90740
Phone: 714/823-3000
Email: Debbieaubert@the
Website: www.thestructurescompany.com
ContractJobHunter Home Page