Job Listing Description

Fuel Cell Assembly Mechanic

Fuel Cell Assembly Mechanics needed for direct hire long term positions.
Opportunity to work direct for the premier commercial aircraft manufacturing company in the US.

Mechanics in this position perform various procedures to accomplish fuselage and wing joining. Work is performed on composite / metal aircraft with occasional sealing.
  • Assemble and install parts, structural components and sub-assemblies to build and attach major wing assemblies.
  • Assemble, install, connect and rework plumbing and electrical components and systems.
  • Perform continuity checks on wire bundles and electrical components.
  • Locate work area using drawings which specifies airplane number, section number, and three-point location.
  • Set up assembly tools per tooling instructions or drawing.
  • Locate tools and/or parts on airplane using tooling holes, pilot holes, K holes, or by hand, per drawing or tooling instructions.
  • Align parts and secure in place using Clecos or tooling/hand clamps.
  • Check for good edge margins and alignment.
  • Shim and/or trim parts as required.
  • Drill pilot holes using drill motor and proper size drill bit(s).
  • Drill, ream, countersink full size holes in parts/assemblies, in proper sequence and to correct size using drill motor.
  • Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners.
  • Use solvents to clean surfaces prior to sealing or assembly.
  • Apply sealant, alodine, primer, adhesives and special finishes.
  • Handle and dispose of hazardous materials in approved manner.
  • Install fasteners by correct type, size and in correct sequence per drawing, using correct tools (e.g., rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner).
  • Obtain two way radio and confined space flag, adhering to Communications System for Confined Hazardous Areas rules, per company procedures.
  • Operate mechanical lifts of various types to locate parts/assemblies into position or to perform assembly work.
  • Prepare, assemble and install tubing, standoffs, valves, regulators, compressors and ducts, using fasteners per drawing.
  • Install pre-assembled plumbing systems (e.g., hydraulic modules; smoke detectors, fire extinguishers, air, water and fuel systems), using ground straps and wires, clamps, lubricant and hand/power tools (e.g., screwdrivers, torque wrenches, nut runners).
  • Install wire bundles and electrical components using production illustrations and wiring diagrams.

Exposure to aluminum, titanium, steel, magnesium, exotic alloys, plastics, composites and hazardous materials. This position will require working in confined spaces of the wing fuel cells for extended periods. Employees crawl through an opening 17.75" X 10.00" in order to get inside the fuel cell. Employment in this position also requires, standing, reaching, turning, twisting, stooping, kneeling, crouching, squatting, crawling, pushing/pulling, working with sealants, paints and other hazardous materials and the use of personal safety gear for face, eyes, hand and ears.
  • Position will require working in confined spaces of the wing fuel cells and crawling through an opening 17.75" X 10.00".
  • High school graduate or GED preferred.
  • Positions open to all US Persons.  “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee.

Job Number: 1710078608
Job Location: Everett, WA
Duration: 24 months
Input Date: 12/11/2017
Last Updated: 09/18/2018
Attention: Camille Zunker
City, State: IRVING, TX 75062
Phone: 214/647-9600
800 Phone: 800/270-4737
Fax Phone: 214/647-9630

Previous Listing       Next Listing
Back to Abbreviated Search Results
Back to Complete Search Results
Back to Advanced Job Search

Phone: (425) 806-5200
Fax: (425) 806-5585
ContractJobHunter is a service of:
C.E. Publications, Inc.
P.O. Box 3006, Bothell, WA 98041-3006, USA
The content of this website is Copyright 2018 C.E. Publications, Inc.